RSS
 

Posts Tagged ‘replace’

How to replace the battery on the iPAQ 3800 and 3900 Series

09 Nov

Before starting the installation, please … – Be careful when handling and Apple ibook g4 battery. – Care of common sense in handling the battery as to not bend (ie, bending), away from metal, away from extreme heat, etc. – Make sure all the data into iPaq have been saved.

- Care of common sense in handling the Battery as not to bend (ie, bending), away from metal, away from extreme heat, etc.

- Make sure that all data were saved in iPaq.

- Read all instructions before your first attempt to replace the Dell XPS M170 battery. This will help you visualize the process before it even began.

1. Turn the power off, and make sure the reset button on the bottom of the unit is turned off to ensure the power is completely off.

2. Take pen from iPaq before continuing.

3. Using a Torx T6, get the four screws out of each corner. Make sure you do not lose the screws. Split the back cover of the main body by using your fingernail or other device such as a flat Phillips screwdriver. Make sure you

Do not scratch the surface when using a screwdriver.

4. Once the back cover is separated from the main body, open the back cover from the top. Do not leave everything the way that HP Pavilion DV2000 battery is attached to the motherboard via a flexible connector PCB. Note: A hard reset slide the door lock button and stylus are not attached to the body, and therefore, they can be loose as the back cover is removed. They are easy to rear, but it is wise to take note of their location and position.

5. As you remove the back cover carefully, you will see a connector between Compaq NX7010 battery and the main board. Carefully remove the connector Battery. Please note that the Battery is glued to the back cover, and can be removed after

Unplug the connector on the main board.

6. Once you have the old Battery removed, align the new Sony vgp-bps9 battery so that the edge of the Battery which is closest to the connector goes to the bottom (for example, the side is recorded on top).

7. Press firmly on the connector Battery. Make sure all corners are firmly inserted.

8. From the bottom, reinsert the backcover. Do not force the lid when closed. This means that the Apple A1022 battery is not properly installed on the back cover. Just realign the stack so it is secure.

9. Insert four screws back and turn the key to reset and power button, in that order, to ensure that the device operates normally.

10. You must fully charge the Battery, And let it charge for more than 30-60 minutes after the full load indicator is lit. This ensures that the  Dell latitude d620 battery is fully

 
Comments Off

Posted in how to, News, technology

 

Replace laptop battery for the Core Detailed

14 Sep

At present, Network On On how to purchase and use Notebook PC Articles everywhere, and on how Solution Notebook Fault Articles are rare. In view of this, bubble network notebook channel decided to notebook Maintenance industry to a major Secret, help the users knowledge and understanding of notebook computers a failure after to face the industry.

The importance of self-evident for notebook Battery . If there are no batteries, laptop will become desktop PC or one machine.Laptop Batteries Internally by Batteries And protection panels, batteries is responsible for electrical storage the work to protect the board in charge of security . Batteries are consumable items, each with a time can causeCapacityThe attenuation, it will have a direct decision laptop battery is good or bad .

Notebook battery life Shorter, laptop battery can not be used, laptop batteries a sudden power-down (such as : battery sudden from 40 % to 10%), notebook battery charging less power (for example: the battery charge to 30%-40 % Not move ), notebook battery and many left case of a sudden shutdown, these circumstances are likely to be batteries -capacity down or batteries damage caused by . Of course, there may be due to protection board hardware damage, but this possibility is very small.

If you find your notebook more than failure, it is necessary to deal specifically with laptop battery repair operations the company to check out . Below, we give us a presentation to the laptop battery for batteries the whole process .

First, we to use professional equipment detect the problem. detection Battery fault instrument there are many, such as : Texas Instruments product, MAX products, Ateml products, and even some personal home-made products. Our company most commonly used is the Texas Instruments (United StatesTexas ) EV2300.

Once detected a battery failure, should be prepared to laptop Lenovo Thinkpad x61 Battery change batteries of online Circulating a statement – laptop battery fails, you can into the refrigerator or the depth of charge and discharge or pulse current activation method of repair. This is wrong .

If the nickel-metal hydride batteries or nickel-cadmium batteries, does by the depth of charge and discharge the method, the part of the repair ( not fully repaired .) However, we now use laptop computers, equipped with are lithium batteries. Li-ion
Dell Inspiron E1405 Battery failure, are basically because the batteries positive and negative material occurred disintegration . This situation is not reversible, so can not be by the above method repaired . Can only be by Replacement Batteries and decryptedUnlock, for repair.

To laptop battery change batteries, first have to tell you about the laptop Inspiron E1705 Battery structure. Laptop battery can be divided into three parts: the shell, batteries group and protection board. In general, the laptop battery can be divided into three parts: the shell, batteries group and protection board.

  • Shell, which is the laptop Dell XPS m1210 battery casing . According to bonding the different ways of can be divided into : snap type, ultrasonic adhesive type and glue -type .
  • Batteries group, that is, the batteries by in parallel, a serial fashion together. In accordance with the parallel series combination of the different can be divided into : 2 and 3 strings ( most common), 2 and 4 string, 2 and 2 series, 3 and 3 strings and 3 and 4 strings ( relatively rare ).

Note : 2 and 3 series means, first two batteries in parallel together, then 3 groups like parallel to the together batteries in series. 2 and 3, series a total of 6 batteries, that is, we usually say that the 6-cell lithium Dell Latitude D630 Battery.

  • Protection board, which is an based on SMB1.1 agreement board, with power management functions and discharge management.
  • Protection board, a piece of based on SMB1.1 circuit board, above 3ChipThey are: the battery meter management chip, charge and discharge management chip, and serial EEPROM memory chips.

Protection of plate the front has a HP 530 battery measurement management chip and charge-discharge management chip. Protection board on the back with a serial EEPROM memory chip, the protection panels Decrypt and unlock are two different things. In short, only be decrypted can into the battery managementSystemOnly the battery management system unlock can change the battery the parameters of and use information. If only changing batteries, do not unlock, you can not achieve satisfactory results (eg : battery only charging to the last recorded full charge capacity, the battery management information shows maintenance used before the number of ) .

We use professional equipment and related software the protection board to decrypt to unlock. Of course, according to battery management chip design manufacturers different, use the appropriate equipment. Use of specialized equipment and related software the protection board to decrypt to unlock, according to Dell Vostro 1720 battery management chip design manufacturers different, use the appropriate equipment. Protection board decryption Unlock software, If the protection board hardware damage, we also use the oscilloscope, multimeter and logic analyzer.

Get protection board, the respect of the handling batteries of the . Now, I ‘ll introduce about batteries sorting, matching and composition. First, we want to use sub- capacity cabinet and internal resistance of meter on the batteries the capacity, internal resistance, voltage, sorting, pick out various parameters compared similar were with groups. Pick out in all aspects parameters are relatively similar of the distribution group. Then, we will use spot welding and nickel films, the batteries together.

With spot welding and the Nickel plate will be batteries grouped together. A nickel plate, there is nickel film. Nickel-plated sheet main material is iron, in fact, in the iron on the thin plating layer of nickel, per unit weight of the cost than the nickel film lower 60 times .

Speaking of nickel plate, a small trick can tell youShareIt. Our company uses the nickel film, all with rounded corners . And the common flat of nickel piece, compared fillet nickel plate with the anti- piercing, etc., can effectively prevent short circuit. On the protection board Decrypt the unlock, on the batteries combination of finished, you can put shell to protect the plate and batteries assembled together.

The shell to protect the plate and batteries assembled with assembly process, the maintenance staff to maintain the most serious working attitude. Laptop Dell Inspiron 1525 Battery pack, it is best to use good insulation material. Please see the above two pictures, the former is imported insulation materials, high temperature, anti- puncture, anti-aging, etc; which is textured paper, insulation is poor, cost than the former lower 2 times .

Sticky shell, the test is no problem to connect to the user. Maintenance after the battery, with the new factory the Dell Inspiron 9300 Battery is similar to the need for the first charge and discharge calibration. We recommend that : first, harge 10 hours (charging process, we can Power Work), charge 10 hours after the call on the finish . Cycle the above steps 2-3 times to achieve the best results .

 
Comments Off

Posted in how to, technology

 

How to replace the hard drive from notebook

22 Jul

As the faulty operate and power sudden off, our laptop hard drive may fail. Or our hard drive is too small to store the enough Documents music and movie. In this situation we should replace a big new hard drive for our laptop. But the work is not easy as the laptop battery light thin and Fragile particularity. So we must do everything carefully in the course of replacing the hard drive.

Remove the Hard Drive must notice the following instructions

  • NOTE: Dell does not guarantee that you will provide support for the acquisition of the hard drive or from a source other than dell
  • Note: Before you begin the procedure in this section, Product Information Guide please follow the safety instructions.
  • However, if the Inspiron 1100 Battery drive is still hot, remove the hard drive from a computer warning: Please do not touch the metal housing of the hard drive.
  • Note: Before removing the hard drive to prevent loss of data off the computer. Meanwhile, please do not remove the hard drive when the computer turn on or sleep state.
  • Note: Hard drives are extremely fragile. Be careful when handling the hard drive.

Removing hard drive

  1. Follow these steps before you begin.
  2. Turn the computer over and remove two screws of hard drive.
  3. spears_h

    1 Screws (2) Two Hard Drives

  4. Note: Although not on the computer hard drive and store it in protective antistatic packaging ( “protection against electrostatic discharge”, see the Product Information Guide).
  5. Slide the hard drive of your Dell XPS M140 Battery computer.
  6. Down to separate the cover from the hard drive (one from each side of the cover of one hard drive), then remove the two screws 2.
  7. spearsa3

    1 Hard drive cover 2. Two Screws (3) Three Hard Drives

Replacing the hard drive

Note: Before you begin, and begin the procedure in this section, Product Information Guide please follow the safety instructions.

Note: Hard drives are extremely fragile. Be careful when handling the  hard drive.

In order to secure the cover to your hard drive and hard drive cover, please tighten the two screws 2.

Note: Use to evenly apply pressure, then slide the hard drive. Excessive force may damage the Sony VGP-BPS8 connector.

To be attached to the drive bays are full, and then slide the hard drive.

Replace Two screws to protect the VGP-BPS9 hard drives.

Install the operating system of your computer if necessary ( “to restore your operating system please see the” Your owner’s manual).

When you install the drivers and utilities for your Dell Inspiron 6400 Battery computer ( “” owner’s manual to see if necessary to reinstall the drivers and utilities).

Now all the work are done. You can use you laptop to listen music watching movie or download more software from internet.
http://www.laptops-battery.co.uk/ hopes that help you.

 
Comments Off

Posted in how to

 

How to replace the hard drive from notebook

03 Jul

As the faulty operate and power sudden off, our laptop hard drive may fail. Or our hard drive is too small to store the enough Documents music and movie. In this situation we should replace a big new hard drive for our laptop. But the work is not easy as the laptop battery light thin and Fragile particularity. So we must do everything carefully in the course of replacing the hard drive.

Remove the Hard Drive must notice the following instructions

  • NOTE: Dell does not guarantee that you will provide support for the acquisition of the hard drive or from a source other than Dell.
  • Note: Before you begin the procedure in this section, Product Information Guide please follow the Dell C1295 safety instructions.
  • However, if the Inspiron 1100 Battery drive is still hot, remove the hard drive from a computer warning: Please do not touch the metal housing of the hard drive.
  • Note: Before removing the hard drive to prevent loss of data off the computer. Meanwhile, please do not remove the hard drive when the computer turn on or sleep state.
  • Note: Hard drives are extremely fragile. Be careful when handling the Dell INSPIRON 5100 Battery hard drive.

Removing hard drive

  1. Follow these steps before you begin.
  2. Turn the computer over and remove two screws of Latitude D520 Battery hard drive.
  3. spears_h1 Screws (2) Two Hard Drives
  4. Note: Although not on the computer hard drive and store it in protective antistatic packaging ( “protection against electrostatic discharge”, see the Product Information Guide).
  5. Slide the hard drive of your Dell XPS M140 Battery computer.
  6. Down to separate the cover from the hard drive (one from each side of the cover of one hard drive), then remove the two screws 2.
  7. spearsa31 Hard drive cover 2. Two Screws (3) Three Hard Drives

Replacing the hard drive

Note: Before you begin, and begin the procedure in this section, Product Information Guide please follow the safety instructions.

Note: Hard drives are extremely fragile. Be careful when handling the  hard drive.

In order to secure the cover to your hard drive and hard drive cover, please tighten the two screws 2.

Note: Use to evenly apply pressure, then slide the hard drive. Excessive force may damage the Sony VGP-BPS8 connector.

To be attached to the drive bays are full, and then slide the hard drive.

Replace Two screws to protect the VGP-BPS9 hard drives.

Install the operating system of your computer if necessary ( “to restore your operating system please see the” Your owner’s manual).

When you install the drivers and utilities for your Dell Inspiron 6400 Battery computer ( “” owner’s manual to see if necessary to reinstall the drivers and utilities).

Now all the work are done. You can use you laptop to listen music watching movie or download more software from internet.
http://www.laptops-battery.co.uk/ hopes that help you.

 
Comments Off

Posted in how to

 

How to replace the Dell Processor Thermal-Cooling Assembly

16 Apr

After used for a long period (perhaps 15- 24 months), our notebook body heat is increasing too hot while working for sometime. As more and more programs are install into our notebooks, the laptop battery CPU and processor works hard and take out a lot heat. Then we should replace the Processor Thermal-Cooling Assembly.

I take the Dellâ„¢ Inspiron 1525/1526 Service Manual Dell Processor Thermal-Cooling for example. Gernerally the whole process should follow the 2 steps : 1 .Removing the Processor Thermal-Cooling Assembly. 2. Replacing the Processor Thermal-Cooling Assembly.

Removing the Processor Thermal-Cooling Assembly

CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.

  1. Follow the instructions in Before You Begin.
  2. Turn the Dell Latitude D520 Battery computer over.
  3. Remove the eight captive screws securing the back cover and remove the module cover.

    spearsb3

    The 1 : module cover. 2 : captive screws (8)

  4. In sequential order, loosen the five captive screws securing the processor thermal-cooling assembly to the system board, then carefully lift the processor thermal-cooling assembly out of the Dell Latitude D600 Battery computer.

    spearsc4

    1: captive screws (5). 2: processor thermal-cooling assembly

Replacing the Processor Thermal-Cooling Assembly

CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.

  1. Align the five captive screws on the Dell Latitude D830 Battery processor thermal-cooling assembly with the screw holes on the system board.
  2. In sequential order, tighten the five captive screws to secure the processor thermal-cooling assembly to the system board.
  3. Replace the module cover and tighten the eight Sony VGP-BPS8 captive screws.

The detail content from dell.com. Laptops-battery.co.uk Hopes that help you.

 
Comments Off

Posted in Gadgets